How To Fix A Service Power Steering Light On The Dashboard?

Usually, when warning lights appear on our vehicle’s dashboard, we tend to be concerned. Especially when it’s the power steering warning light. It would mean a total power steering failure, making the vehicle much harder to steer.

This article will discuss what this light means, the cause of this warning light, and how to fix it.

What Does Service Power Steering Mean?

The “Service power steering” warning tells you that your power steering system has faults and immediately prompts you to investigate a possible cause. The reason may differ due to the type of power steering system in your vehicle. If your vehicle uses a hydraulic power steering system, then a leak in the system would be the cause that would result in a low power steering fluid.

In this case, carry out a thorough inspection of your vehicle for any power steering fluid leak. And if there isn’t any sign of a leak, replenish the power steering fluid. And if it’s an electronic power steering (EPS) system, you would notice an illuminated EPS light instead. EPS systems do not use fluids to provide steering assistance.

Now, there are no fluid levels to check, and as such, you would suspect the batteries because If you recently removed and reconnected your vehicle’s battery or required a jump-start for your car, it would confirm this.

What Causes This Service Light to Come On The Dashboard?

Below are some causes of the service power steering light:

1. Low Power Steering Fluid:-

The power steering system relies mainly on having a specific fluid volume to work accurately. And if you take a look under the hood, you’ll notice a small tank where you can pour in the new power steering fluid, and you will notice that there is a minimum level and a maximum level, which are pretty close.

So when the fluid in the system isn’t enough, your pump won’t have a proper lubrication, and the fluid temperature will rise, which could cause your pump to wear out prematurely. All these combined will lead to an early failure of the power steering and will cause this warning to appear.

2. Broken Power Steering Belt:-

The power steering system is connected to a pump run by the crankshaft of your vehicle’s engine. A pulley on the engine turns a belt connected to the power steering pump and thus always supplies the pump with consistent power. Sometimes, the belts could wear and tear, crack, and eventually snap.

When this happens, you’ll know immediately as your power steering will completely give out, and your steering will immediately become extremely stiff and difficult to operate correctly because your power steering pump no longer receives power from your engine.

3. Contaminated Power Steering Fluid:-

Pressure is applied against a specific amount of liquid to operate the power steering pump. In order for power steering systems to function optimally, the fluid in the hydraulic tubes must be free of contaminants, air bubbles, and other liquid intrusions. Contamination regularly occurs due to deterioration or falling apart of tubes and hoses present in the power steering system.

Similarly, moisture could find its way into the fluid, enhancing friction, which eventually leads to the power steering pump and, consequently, the power steering becoming extraordinarily stiff and difficult to control, especially when the vehicle is in motion. This will cause the service power steering warning to appear.

4. Bad Power Steering Pump:-

The power steering pump is a proper mechanical component with many moving parts. Every mechanical component with moving parts will experience wear with time. Seals can wear out, internal components can become warped, and excessive friction could eventually break it down. And sooner or later, the pump would lose pressure, and your steering would become less easy to operate.

Moreover, if your pump were to give out completely, you’d lose every bit of fluid pressure in your system, resulting in the total failure of your power steering you’ll be required to change the pump.

5. Power Steering Fluid Leaks:-

Even the smallest leaks in your fluid lines can cause a loss of fluid pressure. power steering fluid leak doesn’t happen immediately, as most times, it begins with a seal slowly starting to wear out and fail or a hose developing slight flaws.

It might seem like these are small and insignificant problems. They slowly and surely appear as minor problems, which become bigger, eventually leading to a failure of the power steering.

Is It Safe To Drive With This Warning Light On?

It is not safe to drive with the service power steering warning on. Even if you could, it’s not going to be easy, as the steering would become heavy, and steering will be difficult. It will also be near impossible to react to events on the highway; therefore, driving with the service power steering light could lead to a fatal accident.

How Much Does It Cost To Service The Power Steering?

If it comes to repairing the power steering pump, the cost would be somewhere between $200 and $350. Replacing the power steering pump with a brand new one would cost around $400 to $800 depending on the vehicle model or repair shop you take it to.

What to Do When This Service The Power Steering Light Comes On?

It would be best if you did the necessary things whenever the service power steering light turns on while you’re on the road. Below are some of them:

Step 1:- Signal Other Drivers Using Your Hazard Lights

It would be best if you signaled other drivers on the road that there’s a problem with your vehicle. You could do this action by turning on your vehicle’s hazard lights. And by doing this, you’re also allowing them to practice caution when passing or tailing your car.

Step 2:- Carefully Direct Your Vehicle To The Shoulder Of The Road

Examine the road properly for incoming cars and carefully turn your steering wheel to direct your car towards the shoulder of the road. This action would require you to apply extra force while moving slowly, depending on the damage suffered by your power steering system. Also, don’t be in haste to switch lanes. Always keep in mind that you might not be able to counter-steer immediately in emergencies.

Step 3:- Slow Down Until You Reach A Complete Stop

While you pull over to the shoulder of the road, don’t forget to step lightly on the brake pedals, making sure that there aren’t any fast-approaching vehicles before reducing your speed. Also, once you’ve reached the shoulder lane, gradually apply the brakes until you reach a complete stop.

Step 4:- Assess The Severity Of The Issue

After parking your vehicle in a secure spot, carefully proceed to assess the severity of the issue. You could carry out this action by turning the steering left and right to ascertain the severity of the problem.

Depending on the assessment outcome, you could continue driving until you get home or to a mechanic or even have the vehicle towed. Also, make sure to drive slowly and stay on the shoulder of the road to minimize steering inputs. Be highly aware of your surroundings and apply defensive driving at all times.

Step 5:- Call For A Tow Truck

Call for a tow truck if you cannot steer the vehicle properly or are under the impression that you shouldn’t drive your car in such conditions. Make sure that you park your vehicle at a safe position on the shoulder lane, as it could take some time before the tow truck arrives.

Frequently Asked Questions:-

1. What Causes Power Steering to Go Out?

In some cases, too much fluid could cause the valves and seals to collapse because of excess pressure. Or not enough fluid, and the pump can’t exert enough force required to turn your vehicle. Inputting the right amount of fluid would help prevent this issue, but if there be any leaks, the loss of fluid will eventually lead to failure of the power steering.

2. What Causes Electric Power Steering Failure?

The electronic power steering systems fail due to the problems associated with the mounted electric motors. The most likely cause of failure is excessive heat on the motor. And also, an Infiltration of the system environment by dust, water, dirt, or other contaminants will eventually lead to a failure of the EPS.


We hope the above-mentioned information about the service power steering warning light will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.

What Does The Steering Assist Is Reduced Message Means?

Nowadays modern cars are embedded with a list of safety options. That helps the driver to drive the vehicle safely for long distances. When one of those assistances is not working, the car displays an error message to inform the drivers that they are unsafe. What if you’re driving down the street and you notice that your steering has become stiff. And you are finding it difficult to control your vehicle. Next, you see “steering assist is reduced drive with care” on your dash. What does it mean and how do you handle it? What does it mean when you see the steering assist is a reduced error message?

In short, The Steering Assist Reduced error message is a result of the Engine Control Module (ECM) providing an inaccurate coolant temperature reading. The job of the ECM is to read the temperature of the coolant and regulate its temperature accordingly. When the coolant temperature gets too low, it causes the grease in the steering module to harden leading to a stiffer steering wheel. If it happens the steering assist is then engaged by providing more power to the steering wheel.

What Is A Steering Assist?

The power steering control module (PSCM) is responsible for calibrating the power steering system. When temperatures are too low, the grease lubricating the power steering system will harden causing the steering to become stiffer.

When this happens, the PSCM activates the power steering assist which compensates for the stiffness by adding more power to the power steering. This happens smoothly when the temperature sensors provide accurate readings.

What Does The Message Steering Assist Is Reduced Mean?

The reduced error message happens when coolant temperatures fall too low and the sensors do not detect this. It means that the steering assist will not engage leading to you seeing the steering assist as a reduced error message.

This problem is often not caused by a physical defect in your vehicle but just a case of calibration. When this happens, you need to clear any error messages as we will show you later in the article instead of replacing any physical parts.

This is a common mistake most people who experience this problem make. They rush to replace parts and end up losing a lot of money in the process. This is not necessary at all. Another reason why the message may remain on the display screen even when there is no actual issue is when you change the battery or unplug one component or another in your car.

Current history codes that would have been stored in the system. In the case of the steering assist is reduced message, you may find that the steering is working fine even though the error code is coming up. You will need to make certain through a systematic diagnosis and troubleshooting approach that eliminates any potential guesswork.

How Do You Fix Steering Assist Reduced?

Because of the nature of the processes required to correct this mistake with calibration, the form of the error with calibration might mislead. They include conducting an investigation into the customer’s complaint.

The next step would be to follow industry-standard diagnostic procedures. For the best chance at a correct diagnosis, follow these steps: Analyze and record diagnostics errors in all modules.

Clear all diagnostic errors that come up. If diagnostic errors do not clear, it means there is a fault in the vehicle that needs to be looked into and repaired. Update the Powers Steering Control Module’s software to reflect the most recent settings.

The error message steering assist is reduced is generated due to a breakdown in communication between modules. And is generated by the power steering control module. Even if the problem has been resolved, after the error has been thrown out, it appears as though it is still a current problem.

It is represented by the DTC U0415 mistake and is most commonly found in GM’s Sierra, Tahoe, and Silverado vehicles. If this mistake continues to occur, it is recommended that you take your vehicle to a shop and have it inspected by a professional.

However, it is unlikely that any replacement components will be required. Because the error is due to a problem with the algorithm rather than a problem with a physical member.

Some Related FAQs For Steering Assist Are Reduced Drive With Care:-

1. How can you reset the power steering assist fault?

Restarting your vehicle is the most straightforward method of resetting the warning. Turn on and off the ignition and the entire automobile. This will force all of the electrical components in your car to be restarted. The power steering assists problem signal will be eliminated after two or three repetitions of the procedure.

2. What happens when the power assist in your steering fails?

When your power steering fails, the driver will still be able to maneuver the car. It will take more muscle and effort. If the power steering fails when the power brakes fail, you will have to apply considerable force to the brake pedal to slow the car.

3. How Much Does Electric Power Steering Repair Cost?

Auto Repair at its Finest Replacement of the power steering control module costs between $742 and $769 on average. Labor expenses are expected to range between $106 and $134, with components costing $635. This range excludes taxes and fees, as well as your individual car and geographic region.

4. What Causes Failure of Electric Power Steering?

A pump that is operated by the engine provides power steering. Because your engine is linked to your power steering pump, fraying, any stretching, corrosion, or fracture might fail your system immediately.

5. Is it bad to drive without power steering?

Driving your automobile without power steering might result in significant damage to your vehicle’s suspension. Because driving without power steering can be dangerous, it is also prohibited in several states because it might endanger both you and other motorists on the road. When your power steering fails, turning the wheel becomes considerably more complicated than it would otherwise be.

6. How long can you drive without power steering?

The steering pump, rack, and pinion will wear out and overheat if no power steering fluid is present. You might be able to get away with driving with a low fluid level for a short period of time, but driving without fluid for more than three minutes can harm the pump’s gaskets and seals. As a result, driving without a power steering fluid is quite dangerous.


We hope the above-mentioned about the “steering assist is reduced” error message information will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.

What Does The Car With A Screw Light Mean?

Modern-day cars come with more features and electronics than ever before. Warning lights illuminate whenever there is a problem with one or more of your vehicle’s functions. In case you’re wondering what does the car with a screw light mean?

In this article, we’ll be discussing this warning light in detail. Let’s get started.

What Does The Car With A Screw Light Mean?

When the check fuel cap light goes on, a leak has been detected by your car’s computer. Usually, your fuel cap is loose, and if it is, tightening your gas cap will solve this. If the cause is not a loose fuel cap, have a mechanic check the issue. Sometimes a leak somewhere in the system can trigger the fuel cap indicator to light up. Whatever the reason is, if your fuel cap indicator light goes on, do not ignore it.

The fuel cap plays a vital role in your car’s fuel system, preventing fuel evaporation and contamination. You’ll notice that when the fuel cap indicator light is on, there will be a reduction in your engine performance, even if it is a very slight one. Your engine will need to work a bit harder, and most likely, your gas mileage will slightly diminish, and you will be releasing toxic gases into the environment.

Where Is Your Gas/Fuel Cap Located?

If you’re wondering what does the car with a screw light mean, and where it is located? Your car will have a fuel pump icon on your dashboard. It will usually have a bold arrow pointing either to the left or right side of the pump. This indicates which side your fuel cap is located on.

Some cars do not have this arrow. You need to check the icon and see where the fuel handle is located. If the handle is on the right, your gas cap will be found on the right side of your car.

The fuel pump icon’s position does not indicate where your gas cap is located. Newer model cars will have the arrow as an indication of the location of the fuel cap.

What Causes the “Check Fuel Cap” Indicator Light to Turn On?

When you have a loose or faulty fuel cap, fuel evaporation takes place and can, in the long run, interfere with the functioning of your engine system. There are various causes of why your indicator light turns on.

These are some of the reasons:

1. Fuel Cap:-

The most common reason is a loose-fitting or faulty fuel cap. The fuel cap is a vital but straightforward car part. Its role is simple. It seals the fuel in the tank and stops it from evaporating. The fuel cap plays an important part in the evaporative emissions system of your vehicle.

2. Catalytic Converter:-

Your catalytic converter can be located near the exhaust outlet underneath your car. The catalytic converter’s purpose is to change the toxic and harmful substances from your car’s exhaust into less harmful substances. The converter changes substances like nitric oxide, carbon monoxide, and nitrogen dioxide into carbon dioxide and water vapor before being released into the atmosphere.

3. Fuel Filler Neck:-

The fuel filler neck is the basic entry point for fuel in your car. It serves to bring fuel from the nozzle of the gas pump into your fuel tank. Sometimes, a crack in the fuel filler neck causes the gas to leak.

Hence, these are some causes for your question what does the car with a screw light mean and what are their causes?

How To Reset The Fuel Cap Indicator Light?

1. Turn off your engine. Push the button in your car that fuel cap door if there is a button in your car. If your fuel cap door needs a key, use your key to open the door.

2. Open the fuel cap door, and check that your fuel cap tightens securely every time you close it.

3. If you notice that your gas mileage has reduced, have a mechanic check your catalytic converter.

4. Check also for cracks and leaks. Even a tiny crack can make the fuel cap indicator light up. If you have a faulty fuel cap, replace it immediately.

5. It may take several minutes for your indicator light to turn off after replacing your fuel cap. If your indicator light keeps turning on and then goes off after you tighten the fuel cap, you have a loose or cracked fuel cap, which may need to be replaced.

6. No matter how often you tighten or even replace your fuel cap if the culprit is a crack in the fuel filler neck, that fuel cap indicator light will still turn on. Have a mechanic check your fuel filler neck if your fuel cap light keeps turning on.

Therefore, you can try these steps to reset the fuel cap indicator light.

Is It Safe To Drive With The “Check Fuel Cap” Light On?

Yes, you can still drive with the Check Fuel alert light on. You need to know that going with the fuel cap light on will not harm your engine. Driving with your fuel cap light on will not immediately cause you to lose fuel. The car’s gas tank has a flapper valve that stops fuel from spilling if the fuel cap is missing.

The danger lies in having an ignition source like a lit cigarette come close enough in contact with the fumes escaping from the gasoline tank. So, if your Check Fuel light goes on, you can still drive your car, but you will still need to act on the problem.


The above-mentioned information about what does the car with a screw light mean? we hope this will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.

Steering Wheel Wont Turn And Battery Light Is On, What To Do?

Though every one of us loves buying new cars. After a while, those cars turn out to be a depreciated investment as and when problems start occurring. Nothing can be very more frustrating than if you have an important function to attend to and your car’s steering wheel wont turn and battery light is on at the same time.

However, it can get even more frustrating when you don’t know the reason behind what is wrong with your vehicle. In this article, we’ll be discussing the above-mentioned problem in detail. Let’s get started.

Reasons Behind Steering Wheel Wont Turn And Battery Light Is On?

The main reason for the battery light coming on is the alternator that is not providing electrical power to meet the demands of the vehicle.

The stiff steering wheel and flashing battery light may be caused by a serpentine drive belt. If the serpentine belt has broken or comes off it will lead to not providing power and the battery warning light will come on. You may also lose power steering assist.

The serpentine belt is driven by the engine via the crankshaft pulley. It drives the air conditioning compressor, alternator, water pump, and power steering pumps.

How To Fix The Issue Of Stiff Steering Wheel And Flashing Battery Light?

If your vehicle’s steering wheel wont turn and battery light is on. It’s time to get your vehicle inspected by professionals.

1. Inspect The Battery:-

Check your vehicle’s battery for signs of corrosion or damage to the terminals. Remove any corrosion and make sure the clamps are secure on the terminals.

2. Check The Alternator:-

Take a look at your alternator for any loose or missing electrical connections.

3. Look At The Serpentine Belt:-

If you are having issues with loss of power steering, it’s likely caused by the serpentine belt. Look for major cracks or breakages in the belt or complete loss of the belt. Because this worn-out serpentine belt can lead to the cause of problems like the vehicle’s steering wheel wont turn and battery light is on.

4. Check Your Fuses:-

It’s worth looking to see if any fuses are blown and replace them.

5. Test The Battery:-

Test your battery by starting your engine. If the light turns off, you have likely fixed the issue. If the light remains on, you probably have an alternator issue.

Hence, these are some steps through which you can try solving this issue of your vehicle’s stiff steering wheel and flashing battery light.


We hope the above-mentioned information about the issue of your vehicle’s steering wheel wont turn and battery light is on will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.

Why Does Steering Wheel Jerks Left And Right While Driving?

No one likes it when their steering wheel jerks left and right while driving. This is a sure sign that there’s something going wrong with your vehicle. There are multiple potential causes for a shaking steering wheel, and some of them may even surprise you. Let’s see what they are:

Here Is Why Steering Wheel Jerks Left And Right While Driving?

If the road is smooth and your ride still feels jerky, there’s nothing to blame except for the vehicle itself.

1. Tires Out Of Balance:-

This is the most common reason that you might experience a steering wheel jerks while driving. If your tires are out of alignment or out of balance, they may send shakes through your vehicle and to the steering wheel. Shaking from tires that are out of balance is likely to start when you’re going around 50 miles per hour or faster, though it may start to become less noticeable again at higher speeds.

tires out of balance

2. Problems With Brake Rotors:-

If your steering wheel shakes a lot while you’re braking, that could mean that your rotors are out of round. In other words, the rotors have started to wear out, lose their shape, and become warped. In this instance, you’re also likely to feel some vibrations through the brake pedal whenever you press your foot down on it.

3. Worn Suspension Components:-

Unlike problems with the tires and brake rotors, it’s also possible for suspension and alignment problems to cause shaking while driving. Shaking as a result of a worn ball joint or tie rod is more common in older vehicles than newer ones, so this deserves some extra consideration if you’ve been driving the same car for a while.

4. Broken Engine Mount:-

The Engine problems like air induction, fuel delivery, or spark-related issues can be manifested through shaking and can be felt throughout the entire car, but it’s usually the steering wheel that will give you a heads-up before that happens. Problems like this can disrupt the car from running smoothly, resulting in a distinct vibration from the engine compartment.

5. Problems With Brake Pads:-

The front brake system is connected to the knuckle arm, the knuckle arm is connected with the steering rack end, which is connected to the steering column, and then finally the steering wheel. So if the rotor is still in good condition, the possible cause of steering wheel shakes when braking often comes from the brake pads themselves.

6. Brake Calipers:-

A faulty or stuck brake caliper can also be responsible for some vibrations as well, but it’s usually only present in older cars. In this scenario, the steering wheel will only start vibrating at 50 mph or so, followed by a burning smell.

7. Worn Out Brakes:-

A blown engine may not allow you to drive the car, but faulty brakes will fail to stop the car, which is way more dangerous. Normally if there is a brake issue, you will only feel steering wheel vibration while braking.

Hence, these are some reasons behind the cause of the steering wheel jerks left and right while driving.

How To Deal With The Issue Of Jerking Steering Wheel While Driving?

Step 1:-

If the tires are out balance the first thing you need to check in this situation is whether or not all of your tires are properly inflated. If one or more of your tires is flat, it will create a lack of balance that affects your ability to steer the vehicle properly.

Step 2:-

If the tires themselves look fine but the problem persists, it could be possible that the issue lies somewhere in between the tires themselves and your steering wheel. Your axle could have become bent or otherwise damaged by an accident, and this will prevent the tires and steering wheel from communicating properly through the drivetrain. If you notice sudden jerks in the steering wheel, this could be the problem.

Step 3:-

If your steering wheel is wobbling too much, it could be a sign that the wheel bearings, tie rod ends, or ball joints are damaged. To help a mechanic diagnose and resolve this problem, take note of when you’re experiencing the most shake while driving.

Step 4:-

It’s possible that the rotors weren’t installed correctly, and an inability of the brake pads to clamp together efficiently is what’s causing the vehicle to vibrate. Take your vehicle to the auto shop as soon as possible, and the mechanics will take a look to determine if your brake rotors need to be resurfaced, replaced, or simply adjusted.

Step 5:-

The steering wheel jerks left and right while driving could be because of the brake pads. If the rotor is still in good condition, then it’s time to look at the pads themselves. If the vibration gets worse when you apply the brakes. It means the problem is almost definitely somewhere in the braking system. The rotors and the pads are the most likely culprits, but it’s important to investigate the entire system until the problem can be identified and resolved.

Step 6:-

The suspension components can become loose and develop the play. You’ll start to notice some pretty severe vibrations once you get your car above 45 miles per hour or so. It’s best to stop the car at the shop as soon as possible to avoid such problems.

Hence, these are some basic steps that can help you to determine the problem properly. However, it is suggested to take the help of the professionals. To solve the problem of jerking the steering wheel.


We hope the above-mentioned information about the problem of the steering wheel jerks left and right while driving will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.

What Is The Vehicle Dynamic Control Light In Car?

Nowadays modern vehicles are equipped with plenty of advanced systems designed to keep you safer on the road. One of these systems is the vehicle dynamic control light (VDC) which is meant to improve traction.

What Does The Vehicle Dynamic Control Light In Car Means?

The VDC light comes on the dashboard if your vehicle’s stability control system is disengaged. As it works with your car’s anti-lock brake system to provide more traction. The VDC system allows drivers to maintain control of their cars in slippery driving conditions. Usually, the VDC light can be cleared by turning your car on and off.

If the vehicle is understeering, VDC applies the brakes on the outer front wheel by causing it to turn the way it should. The VDC system is consistently monitoring the direction and steering of the vehicle. If there is a problem, the VDC system enables to counteract the loss of traction and wheel slippage.


What Are The Causes Of VDC Light On The Dashboard?

The most common causes of a vehicle dynamic control light are a defective ABS wheel sensor, and a malfunctioning steering angle sensor.

1. Bad Steering Rack:-

The steering rack is responsible for controlling the wheels based on the input from the steering wheel. It is located on the body of the car as part of the steering system. It uses hydraulic fluid, which turns the wheels. If the rack fails or malfunctions, there might be trouble steering the vehicle, causing the VDC light to turn on.

2. Malfunctioning Steering Angle Sensors:-

The job of these sensors is to measure the angle of the wheel as you drive. If the sensors fail or become contaminated with debris the VDC light will come on.

3. Defective Wheel Sensors:-

The VDC system kicks in to reduce the power of the wheel and provide better traction. If you have a faulty wheel sensor, the proper data cannot be sent by which the VDC light will go on, alerting you that the sensor is broken or has debris on it.

4. Defective ECU:-

There are numerous sensors communicating with the car’s computer at all times. The computer is responsible for taking the data from the sensors and translating it into action. As the wheels begin to slip, the ECU needs to cut power to the wheel for correction. If the ECU can’t read the messages from the sensors, it could cause the VDC light to come on the dashboard.

5. Faulty Alternator:-

The function of your vehicle’s alternator is to recharge the car battery. A defective or bad alternator will be unable to recharge your car’s battery effectively and it affects the VDC system. The insufficient supply of power causes the system to disengage and the dashboard light to illuminate.

6. Low Levels Of Brake Fluid:-

The Low brake fluid can lead to brake failure, which will ultimately affect VDC function.

7. Damaged Hydraulic Circuits:-

Every vehicle is equipped with a dual hydraulic system that works as a failsafe should the main brake line fail. The ECU will turn the VDC light on the moment it detects damage to the hydraulic system circuits.

8. Damaged Stator Ring:-

The stator ring and the wheel speed sensor both relay information about rotational speed to the ECU. A damaged stator ring will disrupt this process and produce a lower output voltage that will cause the ECU to turn on the VDC light.

9. Faulty ABS Module:-

Your vehicle’s ABS module regulates the amount of brake pressure applied individually to each wheel. Sometimes the repetitive exposure to the different temperatures damages the circuit board.

Is It Safe To Drive With My VDC Light On?

Your vehicle won’t immediately break down after 20 minutes of driving, the VDC system prevents your car from slipping. That means if you drive with this indicator light on, you are more likely to get into a vehicle accident.

How To Fix The VDC Light In The Car?

Step 1:-

You will need to replace the defective sensor if it is responsible for causing this issue. Sometimes, the sensors can be cleaned, which saves you some money.

Step 2:-

The steering rack can be difficult to replace, it requires more time and the ECU must be professionally reprogrammed.

Step 3:-

The easiest way to fix a vehicle dynamic control light is by checking the trouble codes with a diagnostic scanner.

Step 4:-

Take your vehicle to a professional as they will help to determine the main reason behind the problem.

Step 5:-

A damaged stator ring will disrupt this process and produce a lower output voltage. To diagnose this issue, your mechanic will need to inspect the stator rings for rust or missing teeth manually. You need to replace the damaged stator rings.

Step 6:-

Wheel alignment is essential and plays a vital role in your vehicle’s stability control. The misaligned wheels are responsible for the VDC light to illuminate. You need to fix it by aligning them properly.

Step 7:-

You will need to have the damaged circuits replaced to turn off the VDC light.

Step 8:-

You may need to check for worn-out brake pads and a faulty alternator to have them replaced.


We hope the above-mentioned information about the vehicle dynamic control light will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve all the doubts as soon as possible.

What Does The Steering Wheel With Exclamation Mark Means?

There are a number of dashboard warning lights that can pop on at any minute. Today, we’ll be discussing what the steering wheel with exclamation mark means on the dashboard of your vehicle. Let’s get started.

What Does The Steering Wheel With Exclamation Mark Means?

This light, a steering wheel, and exclamation point indicate that your vehicle’s power steering fluid levels are low or that there is a fault in the system. Only a fraction of car owners goes through their manufacturer’s manual to know the meaning of various warning lights that flash on the dashboard.

Therefore, most of them get confused when the power steering warning light illuminates. The problem is that one cannot tell what has caused the light to flash. The light can only go away after diagnosing and fixing the problem. If left unsolved, it may lead to safety risks.

Where Can I Find The Power Steering System Warning Light?

The power steering warning light on your car’s dashboard is easily recognizable as it may be a yellow, orange or red steering wheel often accompanied by an exclamation mark. In electric power steering systems, an illuminated EPS communicates the same message.

What Does The Power Steering Warning Light Look Like?

The steering wheel with exclamation mark i.e. power steering warning light is often amber or red with the image of the steering wheel and an exclamation mark. If you have an electric power steering, the light might illuminate behind an EPS sign, which stands for electric power steering.

What Causes The Power Steering Warning Light To Turn On?

The problem causing the power steering warning light to appear on your car’s dash varies, depending on the steering system. If your car has a hydraulic steering system, the most likely culprit is decreasing power steering fluid levels. The likely cause for that is a transmission leak within one of the hoses. When you notice the warning light flashing while you’re driving, pull over and check the fluid level.

The problem with driving a car with a flashing power steering warning light is that it damages the power assist. You’ll be able to drive the car, but turning the steering wheel will be a challenge, requiring extra caution when driving.

A temporary solution to the problem is to refill the system with the correct fluid, and the light will immediately disappear. You need to take the vehicle to a certified technician to repair any damages or fissures within the system that cause the fluid leak to fix the problem permanently.

What To Do If The Power Steering Warning Light Comes On?

1. If you drive a car with a hydraulic power steering system, you should check the fluid level by locating the steering wheel fluid reservoir within the engine. It may be marked with a steering wheel on the cap and should have a marked fluid level.

2. If the level is low, you should top it up with the correct fluid as indicated in your car’s manual. Upon starting the engine again, the light should remain dark.

3. Remember that a low fluid level is often a result of a leak in the system and should be evaluated by a specialist as soon as possible.

4. If your car operates with an electronic system, it may be worthwhile to turn your car on and off again.

5. If this does not solve the problem, you should check that all the connections to your car’s battery are correct and undamaged.

Therefore, the steering wheel with exclamation mark light i.e. power steering warning light indicates a problem that should be investigated promptly.

Is It Safe To Drive With The Power Steering Light On?

It’s not going to be easy, as the steering will be heavier and turning will be more difficult. It will also be almost impossible to react to events at higher speeds, so accidents will be far more likely.

However, if you’re far from home. It is recommended that you stop as soon as possible and inspect your car in a safe place.

Either way, the steering wheel warning light is a clear sign that something is wrong with your power steering system. And you should have your car inspected by a qualified technician as soon as possible.


We hope the above-mentioned information about the steering wheel with exclamation mark light will be helpful to all the readers. If anybody’s doubts persist feel free to comment in the comment section below. We’ll try to solve your doubts as soon as possible.